What does f01 mean on a Maytag dryer?

Publish date: 2022-11-21
Main Electronic Control Board Fail

Herein, what does f1 mean on a Maytag dryer?

The "F1" error means that the dryer's thermistor failed. The dryer is reading the thermistor as "open" and the actual part has shorted out. The thermistor is used to read and control temperatures within the dryer.

One may also ask, can you reset a Maytag dryer? Full Reset It is not uncommon to need to reset a dryer after an error code has been resolved or if the dryer shut down to prevent a thermal overload. Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection.

People also ask, what does f01 mean on a dryer?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.

dO dryers have a reset button?

A dryer is simply a large drum into which wet laundry is loaded. Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button.

What does code f01 mean on Whirlpool washer?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. Be sure to unplug the washer before accessing internal components.

How do I fix my Whirlpool f01?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.

How do I reset my Whirlpool Duet dryer?

How to Troubleshoot a Whirlpool Duet Electric Dryer
  • Inspect household fuses or breakers.
  • Close the dryer door firmly.
  • Press and hold the "Start" button for five seconds.
  • Check the display on the dryer for error codes.
  • Press the "Start" button and hold for several seconds to restart the dryer if "PF" appears on the display.

    • How do you reset a Kenmore he2 dryer?

    To reboot or reset the control board on this type of dryer, you can try unplugging it (or shutting off the house breaker) to completely disconnect electrical power for 3 minutes. After restoring electrical power, the control board will sometimes reset to its original factory settings and work properly.

    How do you take apart a Maytag Bravos XL dryer?

    How to Take Apart a Maytag Bravos Dryer
  • Unplug the electrical cord of the Maytag Bravos dryer from the electrical outlet before taking the dryer apart.
  • Locate the screws on the bottom of the front panel and unfasten the screws with a screwdriver, lifting the panel up from the bottom and detaching it from the clips on the top of the panel.

    • How long should a dryer last?

    approximately 13 years

    What does f01 mean on a battery charger?

    INTERNAL SHORTED CELL BATTERY

    How do you run a diagnostic on a Kenmore Elite dryer?

    Hi ben, here is the process for entering the diagnostic mode, (use any button except STOP) press the button and hold for 3 seconds, release for three seconds, press and hold 3 seconds, release for 3 seconds, press and hold for 3 seconds , the mode has been entered.

    How do you put a Whirlpool Duet dryer in diagnostic mode?

    press and hold for three seconds, release for three seconds; press and hold for three seconds. You'll know you've entered diagnostic mode because all the indicators on the console will light up for five seconds and you'll see the code “88” in the Estimated Time Remaining display.

    What does PF mean on a Maytag dryer?

    Power failure

    How do you start a Whirlpool Duet dryer?

    On the control panel of the Whirlpool Duet dryer, and similar dryers, you push both a "Power" button and an actual "Start" button to use the dryer. A cycle knob allows you to select your preferred drying cycle, but the "Start" button must be pressed to start the load of laundry.

    What does f1 mean on a Kenmore washer?

    The F1 error code indicates a problem with the water level pressure transducer signal on the machine control board.

    What does CE mean on a Kenmore Elite dryer?

    The ce error code is for the exhaust of the dryer and with the vent off and it shutting down I would suggest you pull the lint filter and run the dryer.

    How do you reset a Maytag?

  • Unplug the washer for 1 minute from the electrical outlet.
  • Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
  • The motor has now been reset and is ready for you to start a cycle.

    • Does a Maytag dryer have a fuse?

    This fuse is located on the exhaust duct. If the dryer overheats, the thermal fuse opens to cut off power to the dryer. The thermal fuse cannot be reset--if the thermal fuse is open, it must be replaced.

    What causes a Maytag dryer to stop working?

    A faulty or broken thermostat can make a dryer stop working. Replacing the fuse or the thermostat will allow the dryer to work again. A blown thermal fuse from overheating indicates an additional problem, such as improper ventilation.

    How do you diagnose a dryer problem?

    Problem: Dryer Won't Start
  • The door latch may not be engaging. Check the latch for lint and clean it completely so that the door closes properly.
  • Check the power supply, including fuses and circuit breakers.
  • Check the dryer's internal thermal fuse.
  • If you have a push start knob, it may not be engaging correctly.

    • ncG1vNJzZmiemaOxorrYmqWsr5Wne6S7zGiuoZmkYrGwsdJmnWlpXaKyorqMqKVmmV2irrrAwKBknaqpmr8%3D