What is an upstand in the kitchen?

Publish date: 2023-01-04
In kitchen terms, an upstand is a small strip of kitchen worktop, glass or acrylic usually 100-150mm in height that fits in the rear wall edge of your kitchen worktop.

Keeping this in view, do I need an upstand in my kitchen?

kitchen worktop Upstands An upstand should be at least 100mm although some suppliers will fit smaller ones (70mm or so). They still suit the practical purpose of providing a surface against which you can wipe without wetting the wall.

Beside above, do you need tiles if you have an upstand? Tiles are widely used to protect walls behind kitchen work surfaces, and whilst they are suitable in some circumstances (such as behind a cooker hob), we believe that an upstand helps to merge the worktop into the kitchen in a more attractive way. Of course, you can still use tiles above the upstand if you wish.

Also to know, what is the difference between a splashback and an upstand?

Both worktop upstands and splashbacks are an important consideration for any kitchen. Splashbacks are also available in glass and stainless steel to go behind your hob or sink, whilst upstands can be used to bridge the join between worktops and walls throughout the rest of the kitchen.

Do Upstands go behind hob?

The upstand stops either side of the hob then the splashback is above the hob. If that makes sense. Ours is the same as bluntness - just the splashback behind the hob and host and every where else. We have the upstand all the way around, and a mirror as a splash back sitting on top of the upstand.

Do I need a splashback behind my hob?

Splashbacks are essential for maintaining a clean cooking area and seamless kitchen decor. They're screens fitted to the wall behind your hob which capture splatters caused by things like boiling sauces and frying bacon. They can also prevent damage to your wallpaper or paint from heat and condensation.

How are Splashbacks attached?

Attach the Splashback to the Wall In between each strip of foam tape, apply some translucent silicone. Press the splashback firmly against the wall, ensuring it is flush. Wipe away any silicone that squirts from the edge before it dries. Wait for at least 24 hours for the silicone to dry and clean in necessary.

Do you Mitre kitchen Upstands?

2 Answers from MyBuilder Kitchen Fitters Any external joints should be cut with a nice sharp mitre saw or with a sharp hand saw and a mitre block. Attach the 2 using a mitre bond which dries in about 10-15 seconds, this gives a tight joint.

How high is a kitchen upstand?

In kitchen terms, an upstand is a small strip of kitchen worktop, glass or acrylic usually 100-150mm in height that fits in the rear wall edge of your kitchen worktop.

What is a laminate upstand?

Laminate upstands are a superb way to finish off your kitchen design in style. Particularly if you do not want the hassle of tiling or like the appearance of a painted wall, a laminate upstand is both a practical and an elegant choice.

Are laminate Splashbacks heat resistant?

Laminate. An affordable and easy-to-clean option, laminate splashbacks are a popular choice. While heat resistance is limited, laminate splashbacks are particularly stunning when used as a backdrop for white kitchen units.

How tall should a Splashback be?

The minimum splashback height is 450mm from the bench surface. If you are installing with an electric cooktop in mind, then the minimum height of the rangehood above an electric cooktop is 600mm (as is the height of wall unit cabinets).

How do you hide a gap between countertops and walls?

Lay painter's tape along the edge of the countertop and the wall just above the gap to keep caulk off these surfaces. Apply the caulk with a caulking gun. Choose a color that matches the countertop and spread a thin, continuous bead with no voids.

What do you put behind a stove?

Marble, slate and granite tiles are other stone options that are suitable for placement behind a stove.

How much does a Splashback cost?

COST: A mirrored glass splashback will cost you around $450 per square metre, including installation. Again, add $40 per cut-out required for power points. Acrylic splashbacks give the illusion of glass, but they are a more cost-effective alternative and you can install them yourself.

Can acrylic splashbacks be used behind a gas hob?

An acrylic splashback is cheaper than a splashback made from glass. Toughened glass can withstand temperatures up to 400°C. Most acrylic splashbacks are not suitable for use with a direct heat source such as the rear of gas or electric hobs (they have a heat resistance of up to 160°C).

Do glass splashbacks crack?

Yes – our glass splashbacks can be made toughened, which means they are heat resistant – perfect for use behind the hob without the worry that the glass will crack under heat.

Do you need a splashback behind a bathroom sink?

you do need a splashback of some sort at sinks and baths, doesn't have to go all the way up the wall though. you can use paint. Depending on how clumsy and splashy you are, it will need to be washed down with sugar soap at intervals, and repainted from time to time.

How are glass splashbacks fitted?

To fit the glass splashback, work from the bottom onwards. Line up the bottom edge of the splashback with the silicone sealant that you've placed at the junction of wall and surface. From there, ease the rest of the glass splashback upwards whilst pressing it firmly onto the wall.

What is better splashback or tiles?

Glass Kitchen Splashbacks Are Easier to Clean Furthermore, it is more tricky to remove dried on stains on tiles as they sit in any uneven surfaces and, consequently, require a lot more scrubbing and overall cleaning effort.

Is a Splashback necessary?

Why do I need a splashback? Splashbacks are important to protect your walls and cabinetry from moisture and heat, oils and cooking residue. They're important particularly behind your stovetop/hobbs and behind your sink. They are also a great way to bring in some colour, texture and life to your overall kitchen design.

What is a tile upstand?

A tiling upstand is typically a 22mm integral vertical extension that is applied to two or three siles of a shower tray. During installation, this provides a watertight finish between the tray and the finished wall surface.

ncG1vNJzZmiemaOxorrYmqWsr5Wne6S7zGiuoZmkYra0ecCnZK6oo6mur7CMoqVmrJiaeqy105yfnqY%3D