How Big Should curtain rod pockets be?

Publish date: 2023-04-22
A 1 ½” rod pocket should be used on a standard 1” curtain rod or with a decorative rod 13/16” diameter or smaller. A 3” rod pocket should be used on a standard 2 ½” continental or dauphine rod or on a decorative rod 1 3/8” – 1 ½ ” diameter.

Likewise, how do you measure for rod pocket curtains?

Determine Length, Sew Side Seams Measure the circumference of your curtain rod. Add 1/2 inch to this measurement. For example, a standard curtain rod will measure 2 inches around so your rod pocket opening will need to be 2 1/2 inches; add this to the length of your curtains.

Also Know, how do you measure for curtain rods? A good rule of thumb is to have the curtain rod extend three to four inches from each side of the window frame. Using a pencil, make a small mark at the appropriate width on the wall. You may want to use a level to make sure the marks are straight. Accounting for Finials.

Hereof, what is a rod pocket curtain rod?

Rod pocket curtains, also called pole top or casement curtains, are a classic, and classy, way to hang drapery. A casing sewn onto the back of the curtain panel at the top allows the rod to slip through unseen. Panels bunch in gathers on the rod for a soft look with clean lines.

How thick should a curtain rod be?

Choose a curtain rod with a diameter of at least 1 inch (2.5 cm). Thin curtain rods tend to look cheap and can bow under the weight of your drapes if they are heavy. When choosing a curtain rod, look for a rod that is at least 1 inch (2.5 cm) thick for good aesthetics and curtain support.

How wide should curtains be for 100 inch window?

For example, if the window is 100 inches wide, the curtains should be made to 125 inches wide in order for them to hang off the window when in the open position. For an inside-mount curtain, measure from one edge inside the frame to the inside edge on the opposite side.

Do eyelet curtains need to be double width?

You need to allow for both flat panels to be a minimum of one and a half times the curtain pole width. I personally think they look much better at double the pole width. Give or take a couple of inches. This allows the curtains to have enough fabric to allow the pleats to look right when hanging over your window.

What is the size of a standard curtain rod?

Traditional. In traditional style, the curtain rod is about 6 inches above the top of the window, and it extends beyond the window 3 inches on each side. The curtain will hang 3 inches below the bottom of the window sill. This look offers a few advantages.

How wide should curtains be for 60 inch window?

Example: For a 60-inch window with two curtain panels, add 24 inches to 60 inches (window width) and divide by 2 (number of panels) to get 42 inches. The two panels ordered each need to be at least 42 inches wide.

Should curtains touch the floor?

The fabric should just touch the floor or hover half an inch above. This is also a great approach for café curtains (short panels that cover only the lower portion of a window and hit the sill), which work well in spots like the kitchen and bathroom, where long drapes aren't practical.

How wide should curtain hem be?

Standard curtains have a 3 to 4 inch (7.62 10.16 centimeters) wide hem. You'll need to cut your curtains 6 to 8 inches (15.24 to 20.32 centimeters) longer than you want them to be. Shorter curtains might look better with a 2 inch (5.08 centimeter) wide hem.

How do you hem a curtain by hand?

How to Hem Curtain Panels by Hand
  • Lay the curtain panel flat on the table, the wrong side of the fabric visible, the bottom edge toward you.
  • Thread a needle with a 5-foot length of regular sewing thread.
  • Start at the left edge of the hem.
  • Take a small stitch in the curtain fabric, just above the folded hem and 1/8-inch to the right of the first stitch.

    • How do you connect two curtain panels together?

    Instructions for Sewing Curtain Panels Together
  • Unstitch the vertical side seams on two curtain panels that you plan to sew together.
  • Unpick the stitching in the top sleeve and on the bottom hem.
  • Iron the side seam marks flat along the entire length of both panels.
  • Place panels right-sides together and pin.
  • Stitch a 5/8-inch seam end to end, joining both panels.

    • How do you make pleated drapes?

    How to Make Pleated Drapes
  • Measure from the top of the window to the floor and add four inches (10 centimeters).
  • Measure the width of the window.
  • Buy the material according to your measurements.
  • Make one-inch (2.5-centimeter) hems at the top and bottom of the fabric.
  • Lay the drapery fabric on a flat surface, wrong side up.

    • How do you sew curtains with a liner?

  • Measure Curtain and Lining Panels. Use a tape measure to determine length from floor to desired height of curtain rod.
  • Fold and Press Hem. Place fabric on ironing board wrong-side-up.
  • Insert Weights and Sew Hem.
  • Hem Lining.
  • Create Header.
  • Sew Sides.
  • Sew Header.
  • Pleat and Hang Panels.

    • What does 3 inch rod pocket mean?

    A 1 ½” rod pocket should be used on a standard 1” curtain rod or with a decorative rod 13/16” diameter or smaller. A 3” rod pocket should be used on a standard 2 ½” continental or dauphine rod or on a decorative rod 1 3/8” – 1 ½ ” diameter.

    How do you hang rod pocket curtains on a traverse rod?

    How to Hang Non–Pinch-Pleated Drapes on a Traverse Rod
  • Turn the drapery panel inside out and check for the presence of heading tape.
  • Measure the space from the wall to the front of the carrier on the traverse rod.
  • Indicate pin placement marks along the top of the back of the drapes by inserting a straight pin, perpendicular to the top edge, equidistant across the panel.

    • Are drapes out of style?

    Just like a short Chanel jacket, classic pleated drapes never go out of style, can be dressed up or down, and never lose their functionality. Overdressed, overlayered curtains that match the overused wall borders are, indeed, outdated.

    Are pleated curtains out of style?

    Pleated Panels Pleated drapes work best with formal decorating styles. Pleated panels are a classic style of drapery and so never really go out of fashion, although their popularity rises and falls with current trends. They look quite formal, so work best with formal or traditional decorating styles.

    Can you hang rod pocket curtains with rings?

    Specialty curtain rings with clips attached allow you to hang any type of lightweight or medium-weight curtains from a curtain rod. Hooks or curtain ring clips can be used on rod-pocket curtains.

    Can you use curtain hooks on rod pocket curtains?

    The rod pocket is internal so the curtain panel is essentially a simple panel rectangle. Determine the header style you want for your drapery look and in a few minutes, you can transform your curtain panels into drapes that use drapery hooks.

    Can you use regular curtains on a traverse rod?

    You will be able to use your curtains with a regular rod or a traverse rod.

    ncG1vNJzZmiemaOxorrYmqWsr5Wne6S7zGifqK9dl7aoedKhpq6klGKwtr7TmqCnZaKksW68zpyinqyjYq%2Bm